Checkpoint Super-Vee Mag Base # 308

Checkpoint Super-Vee Mag Base # 308

The Super-Vee Mag Base is specifically designed to be used with the 880 Pro Series Laser Levels. The Super-Vee Mag Base is machined from 6061 T6 Billet Aluminum, aircraft anodized and finished with permanently laser engraved graphics. Designed for unsurpassed holding power, we have installed 6 rare earth neodymium magnets that allows the Super-Vee Mag Base to hold 30 times its weight and it’s only 8 1/2" long.

The V-Groove is integrated with radius ends and corners that allow flush alignments to radius bends and/or corners and self aligns perpendicularly to any pipe utilizing a special designed “Vee-Notch” at the center of the base 90-degrees to the main 135-degree V-groove. A Vee-Notch is machined at the center of the base which makes the Super-Vee Mag Base especially useful when checking for tie-in alignments to specific locations on a pipe run using the laser projection. The Super-Vee Mag Base is a development accessory derived from the demand of electricians, pipe fitters and fabricators in the professional trades sector.

Checkpoint Stubby Mag Base # 309

Checkpoint Stubby Mag Base # 309

The Checkpoint Stubby Mag Base is designed to be kept on the instrument "full-time" highlighting a strong compact configuration, super strong mag-ratio, and layout versatility in both US and MM. This super high performing compact 9" x 1" version uses four neodymium rare-earth magnets, has Imperial (U.S.) and metric scales laser engraved for layout aid, V-groove ends for centering, 1/4-20 tripod tapped hole for versatility, two counter-bored holes for permanent mounting on repeatable slide in slide out applications for all the 600 and 880 series laser levels. Fully machined and anodized, this quick handling super strong compact also accommodates the Slope Pin System to set exact slope and grade positive or negative.

The Slope Pins attach under either end of the base as indicated on the base sides and are held in place by the neodymium magnets centered on the flat side. They give exact slopes or grades with no calculation depending on your choice of slope pin size. For example, simply place a 1/4” slope pin at the front or rear location of the Stubby or Magnum base, and the 8-80 will project an exact 1/4” per foot rise or fall depending on the location of the pin (+ or -). Slope Pins are sold either individually or in sets of seven pieces, and come in 1/16” increments (starting with 1/8” slope). Again, each will work with all new Mag Bases and the 3D DMS series.

Checkpoint Magnum Mag Base # 312

Checkpoint Magnum Mag Base # 312

The Magnum Mag Base is designed to be a super fast and versatile layout aid at an even 12 x 1 inches long including a variable slope/pitch "Jack Screw System." It features five neodymium rare-earth magnets for a superior magnetic ratio, is laser engraved with a 12 inch @ 1/8 Imperial scale (U.S.) and will uniquely accommodate the 880 Square series when attached. The patented Jack Screw System allows one to project any intermittent slope or grade with the laser by simple thumb wheel adjustment - or use the same seven piece Slope Pin Set for exact projections of slope/grade as the Stubby base. Centering notches at each end, fully machined and anodized finish also compliment the Magnum series. Great care in the small unseen components such as spring washers and solid brass parts make the feel and the function the professional's choice.

The Slope Pins attach under either end of the base as indicated on the base sides and are held in place by the neodymium magnets centered on the flat side. They give exact slopes or grades with no calculation depending on your choice of slope pin size. For example, simply place a 1/4” slope pin at the front or rear location of the Stubby or Magnum base, and the 8-80 will project an exact 1/4” per foot rise or fall depending on the location of the pin (+ or -). Slope Pins are sold either individually or in sets of seven pieces, and come in 1/16” increments (starting with 1/8” slope). Again, each will work with all new Mag Bases and the 3D DMS series.

Checkpoint 3D Super-Vee Mag Base # 355

Checkpoint 3D Super-Vee Mag Base # 355

3D Super-VEE Mag Base expand the features of your Checkpoint 3D Laser Level with the purchase of this base.

The 3D Super-Vee Mag Base is specifically designed to be used with the 3D DMS Professional Laser Level. The 3D Super-Vee Mag Base is machined from 6061 T6 Billet Aluminum, aircraft anodized and finished with permanently laser engraved graphics. Designed for unsurpassed holding power, we have installed 8 rare earth neodymium magnets that allows the 3D Super-Vee Mag Base to hold 30 times its weight.

The V-Groove is integrated with radius ends and corners that allow flush alignments to radius bends and/or corners and self aligns perpendicularly to any pipe. This makes the 3D Super-Vee Mag Base especially useful when checking for tie-in alignments to specific locations on a pipe run using the laser projection. The 3D Super-Vee Mag Base is a development accessory derived from the demand of electricians, pipe fitters and fabricators in the professional trades sector.

Checkpoint Ultra Mag Laserbase # 400

Checkpoint Ultra Mag Laserbase # 400

The Patent pending, Ultra Mag Laser Base is the newest addition to the Checkpoint Product Line. It features a Class 3A powerful laser and newly enhanced ergonomic design with a threaded front aperture which allows use of Checkpoint's lens' and other accessories. The new high powered laser beam system is accurate 1/4" (.250) at 100' and is 3 dimentionally aligned from all planes of reference, a calibration feature to the Checkpoint Laser Levels.

Features:

The new Ultra Mag Laser Base offers a V-groove bottom to fit radius pipe/conduit work, and 4 neodymium rare earth magnets to add incredible magnetic strength to hold any metal pipe application on the run. The Ultra Mag laser base is CNC machined from Billet 6061 aluminum alloy. Color buff polished and aircraft anodized with permanent laser engraving from Checkpoint's "no compromise" design and finish standards for true pros in their respected trades.

Specifications:

Laser Type: 3A Accurate Up To: 1/4 Inches Length: 8-1/2 Inches Width: 1 Inch Height: 1-1/4 Inches Shipping Weight: 1.00 lbs.